Icarus SoM DK
Developing for the Icarus SoM (nRF9160) has never been easier. The Icarus Dev KIT includes everything you need to jump straight into developing your next connected project with cellular connectivity (LTE-M and NB-IoT), GNSS (GPS), eSIM and nano-SIM, 3-axis accelerometer, NeoPixel RGB LED and LiPo Charger, all in a convenient full-featured Arduino form factor.
Variant:
€119.49 (excl. VAT)
Stock level: Out Of Stock
What Icarus is good at
GPS and Cellular data on the go
Equipped with the nRF9160 modem from Nordic Semiconductor, the Icarus integrates GPS and Cellular data (LTE-M / NB-IoT) all in one.
3 Months of Free LTE-M & NB-IoT Data
The Icarus includes an eSIM with 10MB of free data for 3 months, so you can start testing your prototype immediately (*only in supported countries). After your free trial ends you can choose to get a subscription on actinius.io or use your own nano SIM!
Use the Icarus anywhere, anytime
Power comes in three: the Icarus board has input for a LiPo/Li-Ion battery (with charger!), USB, and Solar Panel input so that you can use the Icarus anywhere and anytime.
Arduino Form Factor Compatible
You can easily install extra components to the extension pins as the Icarus SoM DK is form-factor compatible with the Arduino boards.
Specifications
Processing
ARM® Cortex M33
1 MB Flash
256 kB RAM
Connectivity
Nano SIM and Embedded SIM
LTE Cat-M1
LTE Cat-NB1 aka NB-IoT
Global coverage
PSM and eDRX are supported
Security
ARM® Trustzone®
ARM® Cryptocell 310
SSL/TLS
Supported by the OTAU Platform of Actinius for always secure and up-to-date firmware
Interfaces
— USB (via FTDI UART Bridge)
— up to 18x General Purpose IO
— up to 6x 12-bit, 200 ksps ADC with EasyDMA
— up to 4x SPI master/slave with EasyDMA (can be mapped to any pin; 1 preconfigured for on-board SPI peripherals and default SPI pin headers)
— up to 4x I2C master/slave with EasyDMA (can be mapped to any pin; 1 preconfigured for on-board I2C peripherals and default I2C pin headers)
— up to 4x UART (also with CTS/RTS) with EasyDMA (can be mapped to any pin; 1 preconfigured for on-board USB-UART Bridge)
— I2S (Inter-IC Sound Interface) with EasyDMADigital microphone interface (PDM) with EasyDMA (can be mapped to any pin)
— 4x pulse width modulator (PWM) unit with EasyDMA (can be mapped to any pin)
— Serial Wire Debug (SWD) on standards 1.27mm connector
Sensors and Peripherals
GPS
Low Power 3-axis accelerometer
Neopixel RGB LED
General Purpose Button
Reset Button
Battery voltage reading
SPI NOR Flash 64Mbit
Power
Can be powered from any combination of USB, Battery, or VIN (eg solar panel)
Nominal Operating Input voltage: 4.35V - 10.2V
Max Input voltage (safety rating): 28V
Battery voltage: 3.2V - 4.2V
Over-voltage protection
Under-voltage protection
Low-noise, low power power supply, with output up to 400mA
USB-friendly Li-Ion/LiPolymer charger with MPPT
Low power consumption
Physical Characteristics
Size: 68.5 mm X 55.2 mm
Form-factor and pin compatible with Arduino boards and shields
Questions about the product? Contact us for help.
You can pay with
Need help with ordering?
email us at info@actinius.com for assistance